Products

Secure your project with biometrics - this all-in-one optical fingerprint sensor will make adding fingerprint detection and verification super sim...

sku: DEV-11520The Fio v3 is a new spin on the Arduino Fio hardware powered by the ATmega32U4. While it isn't yet compatible with its Funnel toolkit...

#3931 Whether you're raiding tombs or traversing nuclear fallout wastelands, this is the most heavy-duty enclosure for your project! Weatherproof? ...

The FLORA is small (1.75" diameter). We wanted the smallest possible board for our wearable platform. It's based on our experiences shipping our ow...

Add motion and direction sensing to your wearable Flora project with this high precision 3-axis Accelerometer+Compass sensor. Inside are two sensor...

Your electronics can now see in dazzling color with this lovely color light sensor. We found the best color sensor on the market, the TCS34725, whi...

Add light-reactive sensing to your wearable Flora project with this high precision Lux sensor. The TSL2561 luminosity sensor is an advanced digita...

What's a wearable project without LEDs? Our favorite part of the Flora platform is these tiny smart pixels. Designed specifically for wearables, th...

So, you want lots and lots of NeoPixels? And you want them for less? Not a problem! Here's a sheet of Flora NeoPixels fresh from the (reflow) oven...

This module is the best way to add a GPS to your wearable project. It's part of the Adafruit Flora series of wearable electronics, designed specifi...

256K bit Ferroelectric Nonvolatile RAM     Organized as 8,192 x 8 bits     High Endurance 1 Trillion Read/Writes     45 Year Data Retention     NoD...

64K bit Ferroelectric Nonvolatile RAM Organized as 8,192 x 8 bits  High Endurance 1 Trillion Read/Writes  45 Year Data Retention  NoDelay Writes  ...

sku: SEN-09376 This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much ...

sku: SEN-09375 This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how mu...

Introduction  DEV7TC is a Seven Segment Display Daughter board that plugs into the Compact Daughter Board Connector of a Modtronix PIC based MicroX...

Introduction The FT232BM is the 2nd generation of FTDI's popular USB UART device and the FT232BL is a lead free version of it.  The FT232BQ provid...

sku: DEV-09873 This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact...

sku: DEV-09716 This is the newest revision of our FTDI Basic. We now use a SMD 6-pin header on the bottom, which makes it smaller and more compact...

sku: DEV-09718 The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The ...

sku: BOB-08891  Simple breakout board for the MQ - 3, MQ - 4, MQ - 6 and MQ - 7 gas sensors.  All you need is VCC at 5V, GND, and a resistor to an ...

This is a simple to use USB evaluation board for the GE865-Quad cellular module. All pins of the GE865 are broken out, so you'll have access to the...

sku: SEN-10742 We've revised the Geiger counter once again, this time replacing the switch with a more robust right angle switch. This version also...

#4677This PSRAM is a 64 Mbit (8 Megabyte) serial pseudo SRAM device, organized in 8 M x 8 bits and in a compact SOIC-8 package. It is fabrica...