Products

DEV-12056 Description: Want to start playing with sensors, but don't know where to start? This kit includes a sensor for just about every job. With...

LCD-14048 The SparkFun TeensyView brings you an easy way to add a small, white-on-black OLED to your Teensy development board. The 128x32 monochrom...

SEN-13266The SparkFun MAX31855K Thermocouple Breakout is a simple 14-bit resolution, SPI-compatible, serial interface thermocouple digitizer that m...

TOL-11784  Description: Are you frustrated with the lack of dexterity from most third hands? The SparkFun Third Hand gives you the ability to hold ...

This SparkFun Triple-Axis Accelerometer Breakout is a simple Qwiic breakout for the KX132 digital accelerometer from Kionix. The KX132 is a low-pow...

DEV-12081 Description: The Weather Shield is an easy to use Arduino shield that grants you access to barometric pressure, relative humidity, lumino...

sku: WRL-09588 The XBee Shield simplifies the task of interfacing an XBee with your Arduino. This board mates directly with an Arduino Pro or USB b...

Customer order

Special purchase.

The SPI Shortcut allows you to control SPI pins over USB, allowing for a virtual "SPI Terminal." Using basic serial commands you can access any SPI...

8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any ...

8, 16, 20, and 28-Pin SSOP to DIP break out boards. The footprint was rotated to accommodate different width SSOP devices and can be used with any ...

After months of searching, we finally have what we consider to be the ultimate conductive thread. It's thin, strong, smooth, and made completely of...

After months of searching, we finally have what we consider to be the ultimate conductive thread. It's thin, strong, smooth, and made completely of...

DEV-11930  If you're new to electronics and programming, the RedBoard Starter Kit is a great way for beginners to get their foot in the door. This ...

This is a basic kit components that enables you to control LEDs, reading status of switch on your Raspberry Pi.Kit Contents Raspberry Pi Cover wit...

This is a kit components that enables you to control LEDs, reading status of switch on your Raspberry Pi. Includes a MCP23017 16 channel IO expande...

This is comprehensive electronic kit for the Raspberry Pi. It includes some advance IC such as the MCP3002 ADC and MCP4802 DAC. For measurement a T...

This 4-wire cable is a little over 150mm / 6" long and fitted with JST-SH female 4-pin connectors on one end and premium Dupont male headers on the...

ROB-13656These steppers are a great way to get things moving, especially when positioning and repeatability is a concern.Note: This is a uni-polar ...

sku: ROB-10848These steppers have a threaded shaft, which allows them to be used as a linear actuator. As the motor runs, it moves along the shaft ...

ROB-10846These steppers are a great way to get things moving, especially when positioning and repeatability is a concern.Features Step Angle (degre...

This NEMA 17-size hybrid bipolar stepping motor has an integrated 18 cm (7″) threaded rod as its output shaft, turning it into a linear actuator ca...

This NEMA 17-size hybrid bipolar stepping motor has an integrated 28 cm (11″) threaded rod as its output shaft, turning it into a linear actuator c...

sku: ROB-09238 This is a simple, but very powerful stepper motor with a 4-wire cable attached. Features Step Angle (degrees) :1.8 2 Phase Ra...

Pololu item #: 1204 This small hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 600 mA at 3.9 V, allo...

Pololu item #: 1205 This hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 670 mA at 3.5 V, allowing fo...

This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the mini...

This is a STM32G431 Nucleo board and a CAN-bus shield with two potentiometers, two push button switches and four LEDs. The STM32G431 board is pre-p...

sku: COM-08860 Huge 10mm through hole LEDs. Mood-light an entire wall! Features 465-470nm Blue 3.0-3.4VDC Forward Voltage 80mA Forward Curre...

sku: COM-08861 Huge 10mm through hole LEDs. Features 515-520nm Green 3.0-3.4VDC Forward Voltage 80mA Forward Current 30 degree viewi...

sku: COM-08862 Huge 10mm through hole LEDs.  Mood light an entire wall! Features 625-630nm Red 2.1-2.3VDC Forward Voltage 80mA Forward C...

These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the...

These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the...

These are very bright LEDs. The LEDs are so bright that it hurts to look directly at them. Please take a look at the pictures to get an idea of the...